Home Decoration - Home Sweet Home Heart Family Quote Wall Stickers Art Room Removable Decals DIY

Home Sweet Home Heart Family Quote Wall Stickers Art Room Removable Decals DIY

Rating: 779 ratings / 4.98 average rating

Shipping: £1.00
Total price: £2.00 (0 bids so far)

eBay


Category: Home Décor

Wall Art Quote Sticker - Home Sweet Home This is available in 4 great sizes: Small - H 16cm x L 24cm Medium - H 20cm x L 28cm Large - H 30cm x L 41cm X-Large - H 40cm - L 55cm XX -Large - H 50cm x L 70cm(sizes are approximate)   Your wall art sticker is available in a variety of colours listed below - Please note the sizes will be dependent on positioning We include application tape, already attached to the vinyl, all you need to do is follow the instructions below Please note all parts will be cut separately so you can position the stickers how you would like them. The sizes are approximate and will be dependent on how you position them. The gallery is for ideas you can be creative as you would like. Colours: White, Black, Grey, Hot Pink, Purple, Brilliant Blue, Sky Blue, Arctic Blue, Aqua, Green, Light Green, Bright Yellow, Bright Red, Dark Red, Orange  How to order: Choose the colour required Add this into notes at the time of purchase Included: Wall Quote Decal Stickers  Transfer Tape Please note:   Easy to apply and remove stickers These are single colours and they do not have a background Internal and external use Vinyl is designed to be used for many items. This needs to be applied to a non porous surface   Vinyl Decal Application Wet/Dry Method: CAUTION: Once the shiny bottom “liner” is removed the adhesive is exposed. Do not let the exposed graphic touch any unintended surface. The back of the graphic is very tacky and will tightly adhere to whatever it touches including itself. If the placement is not correct, removing the graphic for replacement will be very difficult or impossible without causing damage to the vinyl. If you are shaky, use the wet method. Measure where you want your decal to be. Then tape in place on 1 side only to use as a hinge, using blue painters masking tape.  Peel the bottom slippery “LINER” layer away from the DECAL and MASK LAYER starting at the opposite side of the masking tape hinge, and slowly remove it. * NOTE: We recommend inserting a wet step here for beginners and larger decals. It allows you to move the decal into place and even remove and reposition it if needed prior to setting up. To use the wet method placement, mist the rocket surface with a mixture of soap and water.  While still holding the PRE-MASK layer away from the smooth surface. Use a squeegee, credit card or any plastic straight edge to help in application. Start from the side with the tape and gently work away from the tape and squeegee out all water and soap. NOTE: The decals have a pressure sensitive adhesive - the harder you rub the harder it sticks, also the longer you let it sit, the stronger the adhesive will adhere. Use your squeegee and apply pressure from the middle to the outward sides, this will remove all water and start the decal adhesion. Let sit for 5 minutes before removing. If your decal appears to not be sticking the fluid is still behind the decal, just squeegee again and let sit for 10-15 minutes. A rub with a soft cloth can also be useful. Now you’re ready to pull off your PRE-MASK layer and view your decal. Gently pull it off, if you see some vinyl start to come up with the PRE-MASK then lay it back down, squeegee, and wait a few minutes and try again. Prick any air bubbles with a pin and rub down. Be sure that outer edges of decal are rubbed down smoothly and all liquid is forced out. This is essential for proper adhesion Tip: * TIP Use a hair dryer to speed the drying process. Again, be patient, and proceed steadily but cautiously. After all the application tape has been removed, wipe area again with paper towel to remove excess water. All Wet Method The all wet method is recommended on decals larger than 10" x 15" in size, when you are not a seasoned pro and when complicated shapes are involved. In general it is much more forgiving and is recommended for most humans.  Be sure that the surface is clean and free from residue. Find center of decal and the surface on which you want to apply it. Hold the decal in place desired and mark two top corners with pencil.  Next you will use your wet application fluid from above and a sponge to wet the adhesive surface only as you expose it. DO NOT wet the protective backing sheet (LINER) or the protective mask layer.  Start separating the decal at one corner and pull it back slowly, keeping the adhesive back of the decal wet sponging on the fluid as you go – once it is wet, the vinyl becomes quite easy to handle and you don’t have to worry about it folding back on itself.  Wet the rocket surface with the same solution mixed previously and position the decal to the marks established in No. 1. Wet hands with solution and rub over decal lightly, smoothing out any wrinkles.  Work out water with plastic squeegee and dry excess liquid with a soft cloth or paper towel. Squeegee the decal from top to bottom beginning at the center. Rub from right from center, and left from center overlapping strokes 50%. Prick any air bubbles that you can’t squeegee out with a pin and rub down. Be sure that outer edges of decal are rubbed down smoothly and all liquid is forced out. This is essential for proper adhesion.  Decal must dry out for 24 hours before adhesion is complete.  440 Series Monomeric Gloss - deTAPE The DeTape 440 Series is a range of gloss opaque monomeric vinyl available in a range of colours with an acrylic adhesive. Face Film Thickness For DeTape 440 Monomeric GlossVinyl Microns: 70µ Millimetres: 0.07mm Mil: 2.73mil Face Film Finish For DeTape 440Monomeric Gloss Vinyl The DeTape 440 Monomeric Gloss Vinyl range of vinyl has a gloss finish. Adhesive Type For DeTape 440 Monomeric Gloss Vinyl The DeTape 440 Monomeric Gloss Vinyl range of vinyl has an acrylic adhesive.MinimumService Temperature For DeTape 440 Monomeric Gloss Vinyl Guaranteed Exterior Life For DeTape440 Monomeric Gloss Vinyl The DeTape 440 Monomeric Gloss Vinyl range of vinyl is guaranteed not to fade for 5 years when placed externally. This year rating is based on a Central European climate so in the UK and Ireland the products will last longer as we have less extremes in our weather. The year ratings are minimums so the product will generally last longer. Minimum Service Temperature For DeTape 440Monomeric Gloss Vinyl The DeTape 440 Monomeric Gloss Vinyl range of vinyl is designed to function in conditions as low as -20°C / -4°F. Maximum Service Temperature ForDeTape 440 Monomeric Gloss Vinyl The DeTape 440 Monomeric Gloss Vinyl range of vinyl is designed to function in conditions as high as 60°C / 140°F.


This auction ends in 12T 18Std 31Min 38Sek

« Back to my search results

Last searches: Home Decoration